Control panel manufacturing.

Control and power panels, motor control centres (MCC) and PLC panels wired in the Nualux factory, from your diagrams or from its own design. Tested with the HT Fulltest3 and CE marked before shipping.

Panels assembled and tested before leaving the factory.

Nualux is a panel builder with its own factory. It assembles and wires control and power panels, motor control centres (MCC) and PLC panels for production lines and plant infrastructure, from the client’s diagrams or from its own design.

Every panel is tested in the factory before going to site. The team measures insulation resistance, continuity and protective earth with the HT Fulltest3, applies the CE marking, and the test report travels with the equipment. Nualux has installed panels built in its factory on production lines from Europe to South America.

Control panel assembly in a factory

What panels Nualux builds.

Three families of panels.

Motor control centre with drives and starters

Motor control centres (MCC)

Direct-on-line starters, soft starters, variable speed drives and motor protection, fed from a common busbar.

PLC panel with modules and an industrial switch

PLC panels

PLCs, distributed I/O (remote I/O), industrial network switches and 24 V DC power supplies.

Main low voltage switchboard with moulded case circuit breakers

Power distribution panels

Main low voltage switchboards (MLVS) and sub-distribution boards with moulded case circuit breakers, switch-disconnectors and busbars.

All leave with a test report, diagrams and CE marking.

What the work includes.

Reviewing electrical diagrams in the factory

With or without design

From your electrical diagrams, or designed by Nualux with layout, thermal calculation and terminal plan.

Wiring a control panel in the factory

Assembly and wiring

DIN rails, trunking, busbars and switchgear mounted in the factory, with labelled power and control wiring fitted with ferrules.

Insulation test on a panel in the factory

Factory testing

Insulation resistance, continuity and protective circuit measured with the HT Fulltest3 before shipping.

Rating plate of a control panel

CE marking

CE marking applied to the panel, with diagrams, terminal list and test report supplied with it.

Control panel packed for shipping

Packing and shipping

Panel protected and packed for road or container transport, with the documentation inside.

Installing a control panel on site

Installation and start-up on site

The team can follow the panel to site for installation, connection and start-up support.

What the law requires from a panel manufacturer.

A low voltage control panel is electrical equipment placed on the market. Its manufacturer is responsible for its conformity and must demonstrate it in writing.

Legal framework: Decree-Law no. 21/2017 (Low Voltage Directive 2014/35/EU), Decree-Law no. 31/2017 (EMC Directive 2014/30/EU) and the EN 61439 series of standards.

The panel leaves with full documentation

The technical file is kept at the factory and the panel carries the test report, the diagrams and the declaration of conformity.

From diagram to shipping.

  1. Diagram review

    The team checks the single-line diagram, motor list, bill of materials and enclosure size, and prepares the layout.

  2. Assembly and wiring

    In the Nualux factory, DIN rails, trunking, busbars and switchgear are mounted, and the power and control wiring is done with ferrules and labelling.

  3. Testing

    Visual and mechanical inspection, point-to-point continuity, insulation testing and earth continuity measured with the HT Fulltest3.

  4. CE marking and shipping

    The team fits the rating plate and CE marking, places the test report and diagrams in the panel and packs it for transport.

Request a quote

What you receive after each visit.

Every panel leaves the factory with the documents the installer, the client and an inspector will need.

Test report

Insulation, continuity and protective circuit measured with the HT Fulltest3, panel by panel.

Diagrams and terminal list

Electrical diagram updated to match what was built, and a terminal list for connection on site.

EU declaration of conformity

The manufacturer’s declaration that the panel complies with the applicable directives, which accompanies the CE marking.

Control panel assembly factory
Job · Brazil

Production line control panel built in the Nualux factory for export.

Related services

The panel is one part of the installation. These are the jobs around it.

All services

Request a quote.

Make your first contact here for a quote. No obligation.

Questions about control panel manufacturing

A panel builder assembles and wires the control panels that power and control industrial machines and installations. The work runs from reading diagrams to mounting protection and automation devices, routing conductors, testing and delivering the panel ready to install.

It is the series of European standards for low voltage switchgear and controlgear assemblies. It defines design verification and routine verification of control panels, including temperature rise, short-circuit withstand, protection against electric shock and dielectric properties.

It is the manufacturer’s declaration that the panel complies with the applicable European directives, in particular the Low Voltage Directive and the Electromagnetic Compatibility Directive. It is backed by a technical file and the EU declaration of conformity.

The panel builder applies harmonised standards such as EN 61439, carries out the routine verification tests, including insulation and protective circuit continuity, compiles the technical file and issues the EU declaration of conformity.

It is a panel that brings together the starters, variable speed drives, thermal overloads and circuit breakers of several motors, fed from a common busbar. It centralises the control and protection of a plant’s motors.

It is an industrial control panel built to the North American UL 508A standard, which sets component selection, wiring and the short-circuit current rating (SCCR) for equipment intended for North America. It follows different criteria from EN 61439.

Yes. Nualux builds from the client’s diagrams or carries out the design, with layout, thermal calculation and terminal plan.

It depends on the number of outgoing feeders and motors, the equipment selected, the enclosure, the IP rating and whether design work is needed. Send Nualux the single-line diagram or bill of materials for a quote.